XC15-45mmF3.5-5.6 OIS PZ Firmware update
Version: 1.12
Last Updated: 15.11.2024
Overview
NOTES
Please read this update after refreshing this page.
- In case of Windows (Internet Explorer / FireFox / Google Chrome), hold down the “Control” key and “F5” key.
- In case of Mac (Safari / Google Chrome), hold down the “Command” key and “R” key.
- In case of Mac (FireFox), hold down the “Command”, “Shift” and “R” keys at same time.
The firmware upgrade is not required if its version is latest.
- Refer to “2) Firmware version checking procedure” in the “Detail of firmware update steps” below to check the firmware version.
Please use your camera and lens with the latest version of firmware.
- If you don’t use them with the latest version, you may not enjoy their full performance. Check the latest firmware version from the link below.
Detail of the firmware update
The firmware update Ver.1.12 from Ver.1.11 incorporates the following issue:
-
The following software issue is supposed to be fixed with Ver.1.11, but it is observed that the same issue is still occurs in rare cases under some shooting conditions. This is the revised firmware to fix the bug even in the above conditions.
“The lens initializes itself unintentionally and automatically retracts once and back to the original position frequently when using the latest X-T50 and X-M5 cameras.”
The firmware update Ver.1.11 from Ver.1.10 incorporates the following issue:
-
A software issue is improved that the lens Improved the phenomenon of the lens automatically sinking and ejecting unintentionally when used with X-M5 or X-T50.
Revised specification from Ver.1.03 to Ver.1.10
-
When the camera (*1) and tripod Grip, “TG-BT1” are connected via Bluetooth, zooming can be controlled with “T/W button” on the “TG-BT1”.
*1:Cameras and firmware versions that have connectivity with “TG-BT1”
・X-H2S: Ver.3.00 or later
・X-H2: Ver.1.20 or later
・X-T5: Ver.1.00 or later
・X-T4: Ver.1.70 or later
・X-T3：Ver.4.50 or later
・X-S10: Ver.2.60 or later
・X-T30 II: Ver.1.20 (*2)
・X-T30: Ver.1.50 (*2)
*2:T/W button on the “TG-BT1” does not function with those cameras.Note-1:
Firmware update for the camera is required to enable this function. Make sure to update the camera firmware to the latest firmware before updating the lens firmware.
List of Compatible Cameras -
The zooming and focusing buttons on the following camera menus will function when the lens are attached with the proper cameras (*3).
Camera menus that will be supported:
(1)[SETUP MENU]➔ [BUTTON/DIAL SETTING]➔ [TOUCH SCREEN SETTING]➔ [TOUCH ZOOM]
(2)[SETUP MENU]➔ [BUTTON/DIAL SETTING]➔ [LENS ZOOM/FOCUSL SETTING]
・ [CONSTANT SPEED ZOOM (8 steps)]
・ [CONSTANT SPEED FOCUS (8 steps)]
・ [CONSTANT SPEED ZOOM/FOCUS (Fn) OPERATION] for switching “START/STOP SWITCH” or “ACTIVE WHILE PRESSING”
・ [ZOOM RING ROTATE]
・ [ZOOM/FOCUS CONTROL RING] for switching “Zoom” or “Focus”*3:Proper cameras and firmware versions
・X-H2S: Ver.1.00 or later
・X-H2: Ver.1.00 or later
・X-T5: Ver.1.00 or later
・X-T4: Ver.1.60 or later
・X-T3：Ver.4.40 or later
・X-S10: Ver.2.50 or laterNote-1:
Firmware update for the camera is required to enable this function. Make sure to update the camera firmware to the latest firmware before updating the lens firmware.
List of Compatible Cameras -
Aperture control parameters have been optimized to improve exposure tracking during movie recording.
Revised specification from Ver.1.02 to Ver.1.03
-
Fix of minor bug.
The firmware update Ver.1.02 from Ver.1.01 incorporates the following issue:
-
The phenomenon is fixed that In rare cases, AE hunting can occur.
The firmware update Ver.1.01 from Ver.1.00 incorporates the following issue:
-
Stability improvement of the lens barrel moving when turning on and off.
Firmware Update Steps
- Check the firmware version.
- Prepare a formatted memory card.
- Download the firmware (zip file) and decompress it.
- Copy the decompressed firmware to the card.
- Put the memory card with the firmware in the camera and update it.
Precaution
If firmware updating fails, the camera may no longer operate correctly in some cases. Carefully read the notes provided here*Always use the fully-charged battery when updating the firmware as a basic manner. Never turn the camera off or attempt to use any of the camera controls while the firmware is being overwritten.
- You can update the firmware from old version directly to the latest one.
- Firmware updating requires approximately 5 minutes.(maximum)
- Once the firmware has been updated, some data of the previous version cannot be restored.
- Please check here if you encounter any problems.
Download
XC15-45mmF3.5-5.6 OIS PZ License Agreement
Please read this Agreement carefully before downloading this upgraded version software (“FIRMWARE”). By downloading FIRMWARE, you are agreeing to be bound by the terms of this Agreement. If you do not agree to the terms of this Agreement, you are not authorized to download FIRMWARE.
Article 1. License
FIRMWARE is the upgraded version of software that FUJIFILM Corporation. (“FUJI”) already distributed to you included with FUJI’s product(s) (“ORIGINAL FIRMWARE”). All copyrights and other proprietary rights to FIRMWARE are retained by FUJI, and nothing contained herein shall be construed, expressly or implicitly, as transferring or granting to you any right, license, or title unless otherwise explicitly granted under this Agreement.
Article 2. NO Warranty
FUJI EXPRESSLY DISCLAIMS ANY WARRANTY FOR SOFTWARE. SOFTWARE IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF COPYRIGHT, PATENT, TRADE SECRET, OR ANY OTHER PROPRIETARY RIGHTS OF ANY THIRD PARTY. IN NO EVENT SHALL FUJI BE LIABLE FOR ANY GENERAL, SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL, INCIDENTAL, OR OTHER DAMAGES RESULTING FROM THE USE OF OR INABILITY TO USE SOFTWARE.
Article 3. Restrictions
You shall not, or shall not have any third party, reverse-engineer, decompile, or disassemble FIRMWARE.
Caution
*Make sure there isn’t any file with the same name in the destination of the firmware to save. If there is a file with the same name, the browser may automatically alter the name of the firmware like the name and (1). A camera will not recognize the firmware correctly with an altered name like that.
Firmware compatibility table
- Please use your camera and lens with the latest version of firmware. If you don’t use them with the latest version, you may not enjoy their full performance. Check the compatibility table below.
